What are the indicators of a bad clutch | Arborist, Chainsaw & Tree ...
Dec 28, 2010 · The clutch area is the only way rotational force can be given to the chain drive sprocket. There is a problem with your clutch. May just be dirty. Can't be anything else. Take it apart and look at it. It may be assembled incorrectly. Find a parts manual and make sure everything is in the correct order.
Husky 61 Rancher Clutch | Arborist, Chainsaw & Tree Work Forum
May 2, 2017 · Been trying to figure track down a decent aftermarket clutch for my 61. Ordered a Hyway and the thread pattern is not the same and will not work. Seems that the crank has coarse threads and new clutch had fine threads. Any idea what I need to order?
How-to on greasing a Stihl clutch bearing? | Arborist, Chainsaw
Oct 9, 2014 · Husqvarnas are a little different with outboard clutches/inboard sprockets. My 353 has a hollow spindle on the clutch side, and a small hole through the side, which lets me pump grease in through the end to the bearing without disassembling the clutch. But I can't wipe off the old stuff, so I am cautious about pumping in too much. Philbert
husqvarna 141 1998-2000 clutch - Arborist, Chainsaw & Tree Work …
Aug 21, 2009 · chainsaw clutch spring for husky141 well an hour and a little blood later and I got the clutch spring and counter plates together and completed the drive sprocket and clutch replacement on my new old husquvana 141 built in 1998'. the only way I was able to do it was with two pairs of vise grips and one flat screw driver..its not easy but it is doeable
Clutch bearing lube: grease, oil, or what? | Arborist, Chainsaw
Nov 8, 2012 · Local repair tech advised that 30w oil was a better choice for clutch bearings as grease tends to dry up and harden between the bearings until they don't turn and the crankshaft gets scuffed. I did see evidence of hardened grease in the bearing, so changed to oil, but seems like the bearing goes dry pretty quick. Any better options to 1.
Alpina p-500 clutch | Arborist, Chainsaw & Tree Work Forum
Dec 5, 2018 · There may well be another clutch setup that will swap in that saw, have done so more than once on older saws that are difficult to find parts for. When looking I took all the physical dimensions and recorded them, then the search through hundreds of junked saws began and as luck sometimes came my way once in a while I had what was needed and ...
Stihl 015L chainsaw clutch - Arborist, Chainsaw & Tree Work Forum
Jul 17, 2012 · The engine runs very well, but I've had to fix a few items as was expected. The chain oiler wasn't working so I took the whole oil pump/tubing assembly apart and blew the crud out of the rubber tubes and now it works fine. Somehow I managed to strip the threads on the nut that holds the clutch assembly to the driveshaft.
Needle Bearing / Clutch Drum Bearing Lubrication ?? | Arborist ...
Dec 1, 2017 · I have a 359 with the outboard clutch. The 359 has a drilled hole in the end of the crankshaft. All you have to do is take off the clutch cover and press the tip of your grease gun to the hole and give it just alittle squirt. Saw Troll has stated that this feature is common to the newer model Huskys with the outboard clutch. Hope this helps you ...
Clutch getting hot | Arborist, Chainsaw & Tree Work Forum
Jan 1, 2005 · Any reason for a clutch to get hot other than drag at idle from weak springs, or drag from the chain brake when it's cutting? Can a clutch actually slip enough during w.o.t. cutting to get too hot to touch?
clutch removal | Arborist, Chainsaw & Tree Work Forum
Jan 17, 2002 · Usually chainsaw clutch is reverse thread. Best to remove spark plug and insert plastic tool to hold piston (not metal!) and ratchet it off. They can be on there pretty tight so some wd-40 can help. Avoid hammering cause you do not want to …