black pipe assembly technique - Love Plumbing & Remodel
May 23, 2007 · For a correct pipe thread you should be able to hand tight the fitting 3 turns, use a anaerobic pipe sealant on thread first then 4 turns with tefon tape, hand tight fitting on to pipe, wrench tight fitting 1.5 to 2 times with 14" wrench for pipe sizes 1/2" to 1" you will never get a leak, for union smear a coat of anaerobic sealent on union ...
How hard to tighten Black Iron pipe? - Love Plumbing & Remodel
Jul 29, 2009 · The reason they make different size pipe wrenches is for different size pipe. Little pipe = little wrench. Big pipe = big wrench. Teflon paste and or tape greatly lubricates the joint and makes if very possible to over tighten the fitting. there should be about 3 threads showing when the joint is right.
Measure black iron pipe - Love Plumbing & Remodel
Sep 3, 2014 · So to clarify. I need to have a 1/2" black iron pipe that is 12" center to center. I need to thread the pipe myself and have two 90's of both ends. I am having trouble getting the pipe to thread on and stay at 12". I cut the pipe at 10 5/8" with the math of the thread engagement. However it always comes up short of 12". Any idea what I am doing ...
Properly tighten black steel gas piping - Love Plumbing & Remodel
Aug 1, 2016 · It is simply a Male/Female fitting that has precise mating services. You do not use any pipe dope on the mating services. The union allows one to join pipes - where each end is fixed. The easiest thing to do is go down to your local big box store and look at them. Take one apart - you will see. Or google "disassembled pipe union".
Mixing brass valves with iron pipe for gas - Love Plumbing
Nov 7, 2008 · I plan to install a 3/4" brass gas ball valve at an existing galvanized "T", followed by 30' of 3/4" black iron pipe, and the final shut-off valve (brass gas valve) at the stove. Is there any problem mixing brass gas valves with either black iron and/or galvanized pipe for a …
Best way to fix leaking fitting in black poly pipe
Jun 12, 2020 · Placing the shut off valve on it would raise the height of the pipe( even with cutting the pipe a bit shorter) at least another 3-4 inches. Pump and everything else would have to be raised to accommodate extra height.Top side I have only 1-2inches of room left to work with. Did try reversing a fitting, and checked foot pounds of both fittings.
How to unthread black iron fitting - Love Plumbing & Remodel
Sep 25, 2012 · A couple of other things you might try if two pipe wrenches won't crack it loose are some PB Blaster on the fitting, and/or cheater handles on the wrenches. FWIW, PB Blaster is an excellent penetrating oil. Many folks try WD-40, but that is not a penetrating oil. It has its place, that this isn't one of them.
Dielectic union between brass and black pipe
Oct 8, 2007 · The 3/4 fittings were down to about 3/8 ID. No wonder I had to crank up the water pressure to get decent system throughput after installing a PRV. Oh well, all that is gone now. Thinking back to the bad old days offshore, we mixed brass and black iron all the time. Corrosion from the outside was the usual failure rather than internal to the system.
mixing galvanized and ungalvanized steel pipe
Sep 7, 2007 · Galvanized and black pipe are the same material. Heating system historically have been installed with black pipe, but galvanized pipe and fittings are used interchangeably. Domestic water systems are a fresh water system, and for those galvanized is the only steel pipe that can be used, but because of rusting concerns, not electrolysis.
Black pipe assembly tips? - Love Plumbing & Remodel
Jul 10, 2017 · I use RectorSeal 5 teflon pipe dope for gas lines. 1) When I use a street elbow right out of a brass valve, it seems to go much further into the valve (1 or no threads visible) that most other pre-cut nipples in regular fittings.
Skip to content