How to change a key cylinder on a 97 Chevy conversion van 1500
Chevy Mechanic: CaseyA925. You need to remove the steering wheel, turn signal control and in the steering column you will find a pin that holds the tumblers in place for the key switch. You can remove the pin and then remove the key tumbler and replace it. Customer.
97 chevy van 1500 vortec v8 wont start cold.... turns over
Dec 13, 2011 · 97 chevy van 1500... 97 chevy van 1500 vortec v8 wont start cold.... turns over but it may take 10 or 20 trys before it fires..... once it starts it runs great and starts normal all day...fuel filter was replaced..fuel pressure is good ..any ideas thanks win nichols
Q&A: Troubleshooting 97 Chevy Express Van Starting Issues
my 97 chevy express van (5.7) starts fine when cold then after it warms up starts running very rough and will barely start again, help me please. Answered in 2 hours by: Chevy Mechanic: Chris (aka-Moose) Chris (aka-Moose), Technician. Category: Chevy. Satisfied Customers: 85,140. Experience: 24 years of experience diagnosing & repairing. Verified.
97 Chevy Van 1500 5.0 I need directions to replace ignition
Oct 16, 2019 · 97 Chevy Van 1500 5.0 I need directions to replace ignition switch ( electrical part ). Hello, my name is James. I will need to make sure we are talking about the same part. The ignition switch is on the steering column under the dash, mounted about halfway down towards the floorboard. It is held to the column tube with two small screws that ...
1997 Chevy Van Fuel Pressure: Q&A on 5.7 Vortec Specs
Chevy Mechanic: Tim Basham. Spec is 60 psi to 66 psi but I have seen starting problems on these if the pressure is below 63 psi. I am working on a 1997 chevy van with a 5.7 Litre with centr. In a 2002 chevy 3500 van with 5.7 small block what should be. 2001 chevy express van 5.7 vortec, what is the fuel pressure.
Q&A: 1997 CHEVY 1500 5.7 ENGINE TIMING - JustAnswer
Align the indent hole on the driven gear with the paint mark on the distributor housing. Ensure that the distributor rotor segment points to the cap hold area. Align the slotted tang in the oil pump driveshaft with the distributor driveshaft. Rotate the oil pump driveshaft with a screwdriver if necessary. Align the flat (1) in the distributor ...
Q&A: 1997 Chevy 1500 Van Wiring Diagram - JustAnswer
1997 chevy 1500 express van 5.7 ... Can i swap fuel injectors from a 1997 chevy express van 5.7 to a 97 ...
P0340 no cam signal. timing at -45. i suspect a broken eire.
chevy: van 1500 4.3l v6..dtc..limp mode..ecm under the vin mode I am working on a 2008 (mfg 11/07) chevy express van 1500 4.3l v6. I have DTC's P0340 Cam Position sensor ckt 'A' Bank 1 & P0341 Cam Position Sensor Range/Performance.
1997 CHEVY 1500 O2 SENSOR LOCATION - JustAnswer
I have 97 chevy 1500 4.3L with a fault code reading P0141 which is O2 sensor heater circuit malfunction (bank 1, sensor. Super Mechanic. 29 yrs. exp., ASE master, cert. in G.M. electrical, a/c, susspension, brakes, electronic steering. 20,098 Satisfied Customers.
Q&A: TROUBLESHOOTING 1997 CHEVY EXPRESS 1500 …
Wisconsin certified emissions state inspector. I am adding a Red Dot rooftop air conditioner to my 1997 chevy 1500 express cargo van. Current engine does not have air. Members enjoy round-the-clock access to 12,000+ verified Experts, including doctors, lawyers, tech support, mechanics, vets, home repair pros, more.